Xi'an University of Architecture and Technology

Modeling Offshore Fire Impact Induced by Subsea Hydrogen Releases

Abstract Offshore hydrogen production has developed rapidly in recent years. Accidental hydrogen releases in offshore environments threaten the safety of hydrogen supply chain. A mathematical model of sea-surface fire induced by subsea hydrogen release is developed using computat...

The Impact of Industrial Clustering on Air Pollution in the Beijing–Tianjin–Hebei Urban Agglomeration: The Mechanism of Technological Innovation

As one of China’s most important industrial clusters, the Beijing–Tianjin–Hebei (BTH) urban agglomeration faces persistent air pollution while remaining a key driver of regional economic growth. In recent years, technological innovation has increasingly supported industrial upgra...

Cold-adapted membrane-aerated biofilm reactor for domestic wastewater treatment in northwest China: Pollutant removal performance and mechanistic insights

Membrane-aerated biofilm reactors (MABRs) have considerable potential for carbon and nitrogen removal from domestic wastewater. However, their long-term performance under high-altitude, low-temperature, and low-C/N conditions remains insufficiently understood. In this study, a pi...

Prediction of Mechanical Strength of AALRS under Extreme Lunar Environments: An Interpretable Stacking Ensemble Model Integrated with Hyperparameter Optimization Algorithms

Abstract Alkali-activated lunar regolith is a promising extraterrestrial material for large-scale construction of lunar bases. However, the complex coupling effects of multiple influencing factors present significant challenges to strength prediction and mechanistic interpretatio...

Effect of spray temperature on microstructure and corrosion resistance of cold-sprayed zinc coatings

Pure zinc (Zn) coatings were prepared on gray cast iron surfaces by cold spray (CS) to improve their corrosion resistance. The effects of spray temperature on deposition behavior, microstructural characteristics and corrosion performance of Zn coatings were investigated. Higher g...

Natural thickness redistribution and axial buckling of non-geodesic continuous variable-angle filament-wound composite tubes

The development of deepwater and offshore engineering has imposed increasingly stringent requirements on the axial-compression stability and load-carrying efficiency of lightweight composite tubular structures. Although continuous variable-angle filament winding enables spatial t...

Hazard assessment of spontaneous plants based on plant diversity: A case study of the Jiahu Archaeological Site, China

This study fills a long-standing research gap in systematic vegetation hazard assessment for Chinese archaeological sites, a field previously dominated by Mediterranean-focused cases. Taking the Jiahu Archaeological Site in Henan as the research object, it explores the correlatio...

Experimental and numerical study on seismic performance of beam-column rigid joints with embedded transition columns in steel archaized buildings

Steel archaized buildings (SABs) commonly use transition columns connecting upper square and lower circular steel tubes. The abrupt sectional change can cause stress concentration and stiffness discontinuity along the column height, yet the influence of embedment in these all-ste...

Assessing architectural interventions in rock-cut heritage: a resilience-based restoration approach at Longmen Grottoes, China

The loss of protective structures exposes cave temples to climatic disturbances, but the environmental effects of their restoration remain insufficiently quantified. This study develops an environmental-resilience-oriented restoration framework integrating historical reconstructi...

Techno-economic assessment of the deployment potential of solar district heating in high solar radiation plateau regions

Solar district heating is a promising low-carbon heating option for high-altitude Xizang, yet county-level assessment methods that simultaneously account for collector-field siting constraints and techno-economic performance remain lacking. This study develops an integrated count...

Seismic performance and flexural bearing capacity of UHPC prefabricated reinforcement cage formwork concrete column-RC ring beam joints

Existing research on ring beam joints is mostly limited to the concrete-filled steel tube (CFST) column system, which has inherent deficiencies in fire resistance and durability. To address this issue, the present study proposes a novel structural configuration that applies ultra...

AMET-YOLO: A Pear Leaf Disease and Pest Detection Model Integrating Multi-Strategy Feature Enhancement and Task Alignment

Accurate and robust detection of pear leaf diseases and pests is important for early warning in orchards, precision control, and intelligent disease and pest management. In natural environments, this detection task is still difficult because target scales vary greatly, lesion bou...

Synergistic Effects of C-S-H Seeds and PCE on the Performance of Fluoroaluminate-Based Shotcrete: Hydration Kinetics and Microstructural Evolution

To address the trade-off between the rapid setting time and low mechanical strength of fluoroaluminate-based liquid accelerating agents, this study investigated the combined effects of synthetic C-S-H seeds and a polycarboxylate superplasticizer (PCE) on their performance. The un...

Experimental analysis and evaluation of a new seismic isolation method for subway stations in the Loess Plateau with localized sand-interlayered strata

Abstract Post-earthquake statistics indicate that the existing seismic measures and evaluation methods for subway stations in the Loess Plateau with locally interbedded sand layers are inadequate. During earthquakes, the station roofs are prone to deformation or even failure, pos...

In Situ Surface Reconstruction of FA-Based Perovskites with Rigid Molecule for Efficient and Stable Photovoltaics

Abstract In the pursuit of commercial perovskite solar cells (PSCs), formamidinium lead iodide (FAPbI3) has become a high-potential material. However, surface FA cations readily deprotonate into volatile amines under light and thermal stress, which leads to the formation of defec...

Digital Inclusive Finance and Coordinated Eco-City Development: An XGBoost-SHAP Analysis

Eco-city (EC) development depends not only on environmental governance but also on the allocation of financial and technological resources. Digital inclusive finance (DIF) may be associated with green development through improved financial accessibility and resource allocation; h...

Robustness assessment of steel frame structures with novel T-stub connections under lateral impact

The extent to which novel T-stub connections (NTC) enhance the collapse resistance of steel frame structures under lateral impact remains unclear, and there is a lack of a systematic quantitative evaluation approach. To address this issue, a component-based modeling methodology w...

REV-based analysis of non-uniform heat transfer in irregular geometries of precast concrete sandwich wall panels

The thermal performance of buildings is largely determined by the weakest point in the envelope. Precast concrete sandwich wall panels are a new type of high-performance, multi-functional integrated component that has been widely adopted. However, local heat loss caused by metal...

Symmetry-Breaking Induced In Situ Electrochemical Oxidation of MnO to MnO2: A Space Group-Dependent Phase Evolution Mechanism

Abstract The electrochemical oxidation of MnO to MnO2 is a fundamental solid-state phase transition process, intimately associated with the evolution of crystal symmetry and space group. From the perspective of space group evolution, this study systematically reveals the transfor...

BIM-based carbon emission prediction model for prefabricated housing design

Driven by the global dual carbon goals, the construction industry faces urgent tasks in carbon emission reduction. As one of the key approaches to achieving low-carbon development, prefabricated housing requires accurate quantification of carbon emissions during the design phase....